Filters
Close

Tools

View as
Sort by

Crankcase Bearing Alignment Tool

Precision ground shaft used for checking alignment of the crankshaft bearings when installed in the case . When used as a bearing installation tool , this tool ensures bearings go in straight and they are parallel to each other. If you have been pressing them in each half individually your bearings could possibly not be aligned to each other and can cause early bearing failure. Comes with protective end caps on the shaft .
$46.95

Cylinder Squish Indicator Tool

This tool is used for accurately measuring squish clearance. Compatible with all Zenoah /Quickdraw/ CY / RCMK RC engines. Also compatible with other engines that use a "vertical" 10mm spark plug. To get the most power from your engine the squish clearance should be set as accurate as possible without the piston hitting the top of the cylinder during operation. Use this tool to measure piston to head clearance. Comes with instructions.
$65.95

Flywheel Nut

Standard flanged flywheel nut used for seating the flywheel correctly . Then remove and install your recoil drive dog or pulley .
$1.25

Fuel Tester

A simple way to test for alcohol in your fuel . Test your fuel every time you get fuel.
$8.95

Light Duty Knife with 5 Blades

K1 Knife comes replaceable super sharp #11 blades and a snug fitting safety cap Precision knife with special screw for extra blade security and stabilization Used on: paper, cardstock, stencils, film, photographs, tape, plastic, wood, cloth, leather, cardboard, cricut, cork, vinyl, foam boards and most other light-weight crafting Used for: cutting art, model making, crafting, car wrapping, vinyl work, carving pumpkins, quilling Used by : graphic designers, hobbyists, scrapbookers, quillers, and crafters and general purpose Includes (1) K1 Aluminum Knife with (1) #11 Blade, .31 x 4.75 in - .8 x 12 cm K1 Aluminum Knife fits with Excel Blades # 5 / 6 / 10 / 11 / 12 / 13 / 16 / 17 / 17A / 21 Made in the USA
$7.25

No. 2 Blade (5)

Replacement blades (5)
$4.00

Oil Mixture Measuring Bottle

1 quart oil mixture bottle . Measure out the right amount of oil for each gallon of fuel .
$6.95

Performance Worksheet

Down load our free worksheet . Take it to the lake and record all of your information from testing . Compare to other testing sessions to find your best setup . Keeps track of what props etc worked per setup . Great information to look over . PDF file. Read below for instructions.
$0.00

Prop Balancer

This is Dubro's Tru-Spin Prop Balancer. FEATURES Completely Adjustable Propeller Balancer Precision-Machined Rotating Wheels to Assure Perfect Balance Easily Unique Over/Under Set-Up Option Accomodates Even Large-Scale Props
$41.95 $35.95

Spring Tool

Tool for removing & installing springs on the hot pipe setup . No more struggling ! Very easy to use . If you have a hot pipe with the external springs , this tool is for you !
$10.95

Super Collet Removal Tool

Use this solid collet plug to remove your super collet without damage. Simply remove the existing insert, and loosen the screw 2-3 turns. Put this removal plug in place, and tighten the collet with two wrenches as you normally would. The collet pops off every time! No damage to the collet or insert. No holding the flywheel! Reusable many times.
$6.95

Water Jacket Installation Tool - V2.

By using this tool , the water jacket is pressed down over the o-rings to properly seat the water jacket .This tool threads into the sparkplug hole / tighten the jam nut to push the jacket down . Next install the 3mm bolts and tighten accordingly . This will lessen the possibility of stripping the small bolt holes . We have been using this style of tool for years . Very handy . Comes with bolt / jam nut / 2 steel washers / 1 nylon washer and a protective sleeve for storage .
$12.95 $8.95

Zenoah plug tool

spark plug removal tool
$5.95 $2.00